2281S-20-6 Dynamic Model Battery Simulator
2281S-20-6 Dynamic Model Battery Simulator
The 2281S-20-6 Dynamic Battery Simulator uses a model to emulate the response of a battery over its discharge cycle. Since the model can be based on the average current of the product that the battery will power, you can estimate battery life and analyze product performance over the life of the battery.
Estimate the battery life of your product
Power your product with the 2281S-20-6 using a model to determine how long the product operates.
- 101-point model contains open circuit voltage and internal resistance as a function of state of charge
- Create a model based on the average current that the product draws
Quick, repeatable testing under any state of battery discharge
Program the battery simulator for any state of charge, such as near the completely discharged state, to determine how a product performs under a low battery condition and to determine the low battery shut-off voltage.
- Program battery open circuit voltage (Voc) and all other model parameters adjust to the open circuit voltage setting
- Alternatively program the state of charge (SOC) and all model parameters adapt to the SOC setting
Unique GUI continuously displays the state of the battery
See key parameters of battery models, including open circuit voltage, internal resistance, remaining capacity, and state of charge.
- View open circuit voltage, measured terminal voltage, and load current on the right battery icon
- View state of charge, amp-hour remaining capacity, and internal resistance on the left battery icon
Evaluate the performance of multiple batteries
Assess the type of battery that will work best with your product by loading multiple models into the 2281S-20-6 and powering the product with each model.
- Load up to 14 models into the 2281S-20-6
- Battery voltage can be as high as 20 V
- Internal resistance can be as high as 100 Ω
Create a model of a battery based on the current drain of your product
Use a Keithley 2450 or 2460 Source Measure Unit (SMU) instrument as an electronic load to discharge the battery and create a model for the 2281S-20-6. The 2450 or 2460 can discharge a battery at very low currents—lower than 1 nA.
- Alternatively, create a battery model from the battery manufacturer's data
- Model both series and parallel configurations of batteries
Use the battery simulator as a precision power supply
The 2281S Battery Simulator has a power supply operating mode with 0.02% source setting accuracy, remote sensing, and 0.05% current measurement accuracy.
- 1 mV voltage setting resolution
- 10 nA resolution on the lowest current measurement range
The Series 2281S Battery Simulator and Precision DC Power Supply innovatively integrates battery simulation with the functions of a high-precision power supply and battery testing.
|How to Accelerate a Power Management Unit Test|
Using the Keithley 2281S Battery SimulatorLearn how a PMU/PMIC can be fully tested efficiently and quickly with a battery simulator.
|Application Note||10 Nov 2018|
|6 Key Challenges of the Internet of Things|
A Guide to Building IoT Ready DevicesMaster the 6 challenges facing IoT makers, designers, and integrators.
Literature number: 37W-60226-1
|How-to Guide||09 Nov 2018|
|DC Power Supply Technical Information||Technical Brief||09 Nov 2018|
|Power Consumption Profiling and Battery Life Analysis Techniques for Portable, Low-Power Devices|
Literature number: 1KW-60969-0
|Application Overview||09 Nov 2018|
|2281S Precision DC Supply and Battery Simulator Quick Start Guide|
The Model 2281S Precision DC Supply and Battery Simulator is a highly sensitive, accurate, programmable power supply that sources stable low-noise voltage, and monitors load currents over a wide dynamic range from amperes to nanoamperes,. It can also test…
Part number: 071343001
|KickStart Quick Start Guide The quick start guide for the Keithley KickStart 2.0 software.
KickStart Instrument Control Software lets you start making measurements in minutes without complex instrument programming. KickStart allows you to do I-V characterization, data acquisition and logging, and power supply control on a variety of Keithley…
Part number: KKS-903-01G
|Model 2281S-20-6 Precision DC Supply And Battery Simulator Reference Manual|
The 2281S Precision DC Supply and Battery Simulator is a high-sensitivity, low-noise, and programmable instrument that sources stable low-noise voltage, and can monitor load currents over a wide dynamic range from amperes to nanoamperes.
Part number: 077114600
|KickStart Instrument Control Software Version 1.9.8 (Windows 10, 8, 7 compatible)|
Easy to use instrument control software.Required for use with KickStart’s High Resistance Measurement App (HRMA).For all other apps, consider KickStart 2 as a replacement.Compatible with Windows 7, Windows 8 and Windows 10.
Part number: KICKSTART-1.9.8
|Selector Guide - General Purpose Power Supplies, Special Purpose Power Supplies, and Electronic Loads|
Literature number: 1KW-60035-2
|Product Selector Guide||09 Nov 2018|
|KickStart Instrument Control Software Version 2.0.5 (Windows 10, 8, 7 compatible)|
"""KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features• Save time by automating data collection of millions of readings.• Set up a multi-instrument test with the ability to…
Part number: KICKSTART-2.0.5
|Description of 2281S General Operation and Battery Simulator Function |
The 2281 is a precision measurement, linear power supply. That is one of its standard operating modes. It can measure low uA and tenths of uA currents with 10nA resolution. It can also capture narrow load current bursts as narrow as 140us. In the…
|FAQ ID: 468851||06 Apr 2018|
|How to configure the Model 2281S-20-6 as just a power supply?|
Model 2281S-320-6 has three functions (high precision power supply, battery test and battery simulator) To configure as a power supply from the front panel for 3.8V at up to 4A: Select Power Supply from the main menu. Press ENTER Select Vset. Use the…
|FAQ ID: 251146||09 Feb 2018|
|2281S Firmware, V1.07|
Part number: 066178501
|Keithley IVI-COM/IVI-C Driver for Series 2280S/2281S Programmable DC Power Supplies - Version 184.108.40.206 (Windows 8, 7, Vista, XP Compatible)|
Part number: 2280S-IVI-220.127.116.11